JKBMS B & BD Series Smart BMS Interface Guide (JK-BXXXX / JK-BDXXXX)

Estimated reading time: 4 minutes

Overview

This article covers the interfaces and connectors available on the JKBMS B Series (JK-BXXXX) and BD Series (JK-BDXXXX) Smart BMS protection boards. It is intended to help users correctly connect and operate their BMS unit.

Note: Interface availability varies by version suffix. Please refer to the naming convention and version comparison table below to confirm which interfaces are included on your specific model.

Quick connection reference: B/BD PC software uses a USB-TTL cable connected to the protection board's GPS port. B/BD displays use the matching RS485 display models. These are different connections: do not substitute a PB TTL-P display or a PB USB-RS485 PC cable.

Naming Convention

For the Standard, HC and HCRPB versions compared here, Standard includes Bluetooth and UART; HC adds CAN and heating; HCRPB adds RS485, an enhanced Parallel Module Interface and a buzzer. Confirm the exact SKU and manual rather than applying this comparison to every model suffix.

For example, the suffix HCRPB indicates the board includes: Heating + CAN + RS485 + Parallel interface + Buzzer alarm.

Applicable Models

  • B Series: JK-B1A8S10P, JK-B1A16S10P, JK-B2A8S20P, JK-B2A16S20P, JK-B2A24S20P, and other JK-BXXXX variants
  • BD Series: JK-BD6A8S, JK-BD6A17S, and other JK-BDXXXX variants

1. Communication Interfaces

Bluetooth

The Standard, HC and HCRPB versions compared here include Bluetooth for parameter configuration and monitoring via the JKBMS App. Confirm the app and settings for your exact model.

UART and GPS: PC Software Connection

For B/BD PC-software communication, use the appropriate USB-TTL cable at the protection board's GPS port. Do not treat a UART label as a guarantee of inverter or third-party monitoring compatibility. Use the model-specific manual for pinout, logic level and communication settings; this guide does not specify a universal baud rate.

RS485 (HCRPB Version in This Comparison)

HCRPB includes RS485 in the version comparison below. This does not mean every B/BD model with a different suffix lacks RS485. Check the exact SKU for interface availability, protocol, cable wiring and settings; generic RS485 distance or network-node limits are not specifications for your BMS.

CAN Bus (HC / HCRPB Versions)

HC and HCRPB include CAN. Inverter compatibility depends on the exact BMS and inverter models, firmware, supported protocol and cable pinout. A CAN port or a protocol label alone does not guarantee compatibility with every inverter of a particular brand. Check the required baud rate in the model-specific documentation.

B/BD Display Connection

Use B/BD-compatible RS485 displays, such as LCD-4.3-RS485 or LCD-2.0-RS485. PB TTL-P displays are not interchangeable with B/BD displays. See the B/BD display guide for display selection.

2. Functional Interfaces

Heating Control (HC / HCRPB Versions)

HC and HCRPB include heating control. Confirm the heating connection, supported load and parameter settings in the manual for your exact board before connecting a heating pad. Do not assume a universal connector type or heating threshold.

Temperature Sensor Interface (NTC)

Use the temperature sensors specified for your exact BMS. Sensor resistance, connector and quantity must be checked against the model-specific manual rather than inferred from the series name.

Balance Leads

The sampling harness connects to individual cells for voltage monitoring and balancing. Verify the connector, every pin and the required cell sequence against the exact board manual before connection.

Important: Incorrect sampling-wire order may permanently damage the BMS. Do not wire by connector color alone.

Main Circuit Terminals

Follow the markings and wiring diagram for your exact board. Do not assume that every B/BD board has separate B−, P− and C− terminals or that charge and discharge terminals can be interchanged.

3. Parallel Expansion Interfaces

Soft Parallel (P-LINK Module)

HC and HCRPB versions of the B/BD Series support soft parallel expansion via the optional P-LINK module, subject to the exact model and module instructions. P-LINK is not for PB-series boards and must not be confused with the PB interface board.

Parallel Module Interface (HCRPB Version in This Comparison)

HCRPB includes the enhanced Parallel Module Interface in this comparison. Use the optional Parallel Module only with a board that has the matching interface, following the board and module instructions. Interface availability does not mean the module is included.

4. Interface Comparison by Version

Applies to the Standard, HC and HCRPB B/BD versions described here. Check the exact model for other suffixes.

Interface / Feature Standard HC HCRPB
Bluetooth ✅ ✅ ✅
UART ✅ ✅ ✅
CAN ❌ ✅ ✅
RS485 ❌ ❌ ✅
Heating Control ❌ ✅ ✅
Soft Parallel (P-LINK Module) ❌ ✅ ✅
Parallel Module Interface ❌ ❌ ✅
Buzzer Alarm ❌ ❌ ✅

5. Safety Notes

  • Always disconnect all power sources before wiring to avoid short circuits or electric shock.
  • Do not hot-plug UART, RS485, or CAN interfaces.
  • Balance leads must be connected in strict cell sequence — incorrect wiring may permanently damage the BMS.
  • If in doubt, contact JKBMS technical support or refer to the user manual for your specific model.

6. Definition of the Port and the Wiring of the Parallel and Heating

Port definition and wiring diagram for parallel and heating interfaces

Related Technical Resources

Find model-family guides in the JKBMS Technical Hub. Compare display families in the B/BD vs PB display overview, and use the PB interface guide for PB-specific connections rather than applying B/BD wiring to PB boards.

Download the manual for your exact model from the Download Center. For wiring or model-identification questions, contact the JKBMS Support Center.

Zurück zum Blog

Hinterlasse einen Kommentar